Frequently Asked Questions

You can use the Echo setting in the menu to help with this. This menu setting sets up a “dead time” after each detected shot so that the shot timer will not trigger on echoes from your surroundings or the sound of a steel target being hit. 0.11 seconds is a good middle-of-the-road setting, but you can change this value if you need. A word of caution – extremely short echo times may require careful adjustment of the sensitivity value to avoid picking up extraneous sounds.

Currently the longest par time you can set it 999 seconds. If this becomes a limiting factor in the future, we can upgrade it with a firmware update.

Yes, your KST1000 can be used for dryfire or airsoft training. You will have to tailor your sensitivity settings for your exact weapon. If your gun is particularly quiet, this can be challenging. First thing is to adjust the sensitivity to pick up your weapon. If it is loud, you may be able to have the KST1000 relatively far away. If not, it may be helpful to position the timer close to where the weapon will be fired. Depending on your weapon system and accessories, the timer will also likely hear other sounds. This can include racking a slide or drawing from a holster.

For both RO and solo operation, it is important to understand where the buzzer and microphone are located on your KST1000. They are on the back of the unit in the upper half of the device. If you are acting as an RO and timing another shooter, you will have the best results if you do not cover the buzzer and mic with your hand. This means that you can face the screen toward yourself while you work. When you are wearing the KST1000 on your hip, try not to block the microphone with clothing. In more sensitive settings, you may find that your KST1000 interprets rough handling, such as quickly removing it from your belt, as a shot. You can eliminate this by making use of the mute function.

Elapsed time is displayed in the center of the front display. This can be used for an RO to see how much time is left in their stage or to see if they missed the par time beep. It does not ever stop. With the KST1000, there is no need to “stop” the timer. Any time that you press GO, it will start a new string.

Your KST1000 can be configured for up to three par times. To enable the first par time, click the enter button on first par time. Use the right or left buttons to select on. Press the gear button to return to the main menu and you will see a time. Use the left and right buttons to change the time. You can then add a second par time as desired, and from there a third as well. It is important to know that you must enable them in numerical order. For example, you cannot enable the second par time if the first par time is disabled.

The KST1000 Shot Timer uses two CR123 batteries. Typical battery life is up to 90 hours of use.

For most situations, this can be left off. But for extremely quiet weapons, the buzzer may be louder than the gunshot so it is necessary for the KST1000 to selectively mute during the buzzer. This means that it will not detect gunshots that happen concurrently with the start beep, which is defaulted to 300 ms. While scrolling through this setting, there are also plus values. These are essentially echo values for the buzzer mute.

When filter is on, it runs the microphone through an electrical filter, but as of now we do not recommend turning the filter on as there should be no need to do so.

Your KST1000 can be configured for fixed or random start delays in the main menu. With the left and right buttons, you can scroll the fixed start delay. Scroll all the way left to turn off the fixed delay. The random line allows you to add random time to the start delay. Again, scroll right and left to change the maximum randomized time. This combination of fixed and random delay will result in a random delay between 2.0 and 3.0 seconds. To change the lower bound, make the adjustment in the start delay line. To change the upper bound, make the adjustment in the random line.

For a quick set up, you can use the preset functionality in your KST1000. This allows you to have five “bins” start delays, par times, etc. Here’s a simple situation where you might find this useful. If you’re going to have a practice session where you are going to bounce back and forth between two drills that have different start delays and par times, you could set up Drill 1 in the first preset slot and Drill 2 in the second preset slot. To change between presets, simply select the top line in the main menu and use the left or right buttons. You can even rename these presets by going into the submenu.

No. While the KST1000 does have Bluetooth in it, it does not connect to any Kestrel or other product.

You can connect the KST1000 to our Kestrel LiNK Ballistics app for iOS or Android via Bluetooth. Once connected ,you will be prompted if a new firmware is available. Simply select Yes and it will begin the update.

Unfortunately this will not be available at the launch of the product. We hope to eventually have this integrated at a point in the future however.

Yes, the KST1000 is rated IP67 which means it should survive being submerged in 1 meter of water for up to 30 minutes.